Hemet, CA · California license 1137822 · C-8 Concrete
(951) 533-8821
Home
Services
Services
Residential
Commercial
Service Areas
Service Areas
Riverside County
San Bernardino County
Orange County
Los Angeles County
San Diego County
Kern County
GalleryAboutBlogContactCall (951) 533-8821
Skip to content

Sealing Concrete Where Winters Freeze

In the valley, sealing is about sun, hot tires and stains. Up in the hills around Aguanga it is a different reason. Winter there means nights below freezing and days that warm back up, over and over, and a slab sitting out in that weather is taking a small beating every time the temperature crosses the line. Sealing is one of the few things an owner can do after the pour that actually changes how long the surface lasts.

Concrete is low maintenance, not no maintenance. Here is what the cold does to it and what sealing really buys you.

What freezing water does inside a slab

Concrete looks solid, but it is full of tiny pores and channels left behind as the water in the mix dried out. Rain and snowmelt soak into those pores. When the temperature drops below freezing, that water turns to ice and expands, and the ice pushes outward on the walls of every pore it fills.

One freeze does almost nothing you could see. The trouble is repetition. Each thaw lets a little more water work in deeper, and the next freeze pushes from a little further down. Over a few winters the top layer weakens and starts to flake off in thin chips. That is called scaling, and once it starts it tends to spread, because the rough surface left behind holds even more water.

A slab mixed with entrained air, countless tiny bubbles that give the ice room to expand, handles this far better. Most of the scaling we get called to look at is on concrete that went in without it.

Why road salt makes it worse

De-icing salt keeps ice from forming on the surface, which is why people use it. It also does a few things concrete does not like. Salty water stays wet longer, so the slab spends more of the winter saturated. Salt lowers the freezing point, which can mean more freeze and thaw cycles on a given night rather than fewer. And the chloride itself attacks the cement paste that holds the stone together.

Plenty of salt arrives on concrete that nobody salted. It drips off cars and trucks that drove salted roads, it gets tracked in on boots, and it washes off a neighbor’s drive. A garage apron or a driveway near the road takes a steady dose every winter whether you buy a bag or not.

If steel sits too close to the surface, chloride that gets down to it starts rust, and rusting steel expands and cracks the concrete from inside. That kind of damage is far harder to fix than scaling.

What a sealer actually does

A good sealer has one main job here, which is keeping water and salt out of those pores. Some sealers soak into the concrete and line the pores so water beads up and runs off instead of soaking in. Others form a thin film on top. Both work by the same idea: if the water never gets inside, there is nothing in the pores to freeze and nothing carrying salt down into the slab.

That makes sealing the biggest single thing an owner can do for a slab at this elevation. It does not make concrete waterproof forever, and it will not save a slab that was badly mixed or finished, but on sound concrete it slows the whole process of scaling way down.

Which type is right depends on the surface. A penetrating sealer changes the look very little and keeps a broom finish grippy. A film sealer can give a darker, richer color on decorative work but can get slick when wet, which matters on a sloped driveway.

Joints are part of the job

Sealing the slab and ignoring the joints leaves the weakest spots open. Control joints and the gaps where a driveway meets a garage or a walk meets a step are the places where water gets straight down into the base and into the edges of the panels.

Joints that have lost their sealant fill up with sand and grit. When the slab warms and tries to expand, that packed grit has nowhere to go, the edges of the joint take the pressure, and they chip and spall. Water sitting in an open joint also freezes there, which pries the edges apart from the side.

So joint upkeep goes with sealing. We clean old sealant and debris out of the joints and fill them with a flexible sealant that moves as the slab moves. It is unglamorous work, and it protects the parts of a slab that fail first.

Timing and doing it right

New concrete needs to cure before it gets sealed, so a fresh slab is left alone for a while first. We will tell you when yours is ready, because it depends on the weather it was poured in and how fast it dried.

Sealer goes on clean, dry concrete. Dirt, oil and old flaking sealer all keep the new coat from bonding, so the surface gets cleaned properly first and given time to dry out completely. Applying on a damp slab, or on a cold day when the sealer cannot cure, is how a coat ends up peeling or turning cloudy within one season.

Fall is the natural time to do it up here, after the summer heat and before the first hard freeze, so the slab goes into winter protected.

How to tell a slab is due

You do not need a calendar to know when concrete wants sealing again. The slab will tell you. Pour a little water on a few spots, in the wheel tracks, near the garage door and somewhere out in the open. If it beads up and sits on top, the sealer is still working. If it darkens the concrete and soaks in within a minute or so, the surface is open again and water is getting into the pores.

Wear is never even. The tire paths and the area right at the garage door lose protection first, while the edges and corners can hold up much longer. Sun-baked sections break down sealer faster than shaded ones. A driveway can be due in the tracks and fine everywhere else.

Other signs are a surface that looks chalky or dull, stains that soak in instead of wiping off, and fresh flaking at the spots where water always sits. Any of those before winter means it is time.

When sealing will not help

Sealing protects good concrete. It does not repair bad concrete. If a slab is already scaling badly, cracked and heaving, or settling at one end, putting sealer over it just puts a shiny coat on the problem. The cause has to get fixed first, whether that means resurfacing the top, repairing the base, or replacing the panels that have failed.

We will tell you which category your slab is in. A lot of concrete that looks rough is still sound underneath and is a good candidate for cleaning, joint work and a sealer.

There is more on sealing for Aguanga properties, and on our concrete sealing service in general.

A few habits that help all winter

Clear ice and slush early so meltwater does not sit and refreeze on the slab. Use salt sparingly, and never on concrete in its first winter. Rinse salty slush off the garage apron when you get the chance. Keep downspouts and sprinklers from soaking the same patch of concrete every day. Watch the joints, and when sealant starts pulling away or grit fills them, get them done before the next freeze.

Have somebody look at it before the cold

If your concrete has never been sealed, or you are not sure what was put on it, the best time to find out is before winter. Do the water test this week. If it soaks in instead of beading, tell us through the contact page or call (951) 533-8821, and we will look at the surface and the joints before the first hard freeze.