People call about an RV pad thinking it is a bigger driveway. It is closer to a parking spot for a small building. The rig sits in one place for months, it weighs a lot, and almost all of that weight comes down through a few tires and a handful of jack feet. On a rural lot out around Aguanga you usually have room to put it anywhere, which sounds like an advantage until you realize the ground is sloped in three directions and the gravel road in was never meant for a long trailer swinging around.
Most of what makes a pad work gets decided before anybody digs.
Picking the spot
The first question is where the rig actually lives, and the answer is rarely the flattest-looking piece of dirt. You want a spot you can reach without crossing a soft patch or a buried line, where the door side faces somewhere you would want to step out, and where runoff from the rest of the property is not going to cross the pad every time it storms.
On a hillside lot, getting a level pad means cutting into the high side, filling the low side, or both. Cut ground is usually firm. Fill is where pads settle, because new dirt placed on a slope keeps compacting under weight for a long time unless it was compacted properly when it went in. We would rather move the pad a little uphill onto cut ground than build the whole thing on a deep fill wedge.
We also look at what is overhead. Trees drop sap and branches, and a rig parked under them all winter sits in shade that keeps the slab damp.
How you are going to back onto it
This is the part that gets forgotten. An RV or a long trailer does not drive onto a pad, it gets backed on, usually with a few tries and some correcting. The pad has to sit where you can line up from the road or the driveway with room to swing, and where a tow vehicle can pull forward to straighten out.
We usually walk the approach with the owner and talk about how they really park. Do you back in from the left or the right? Does the rig need to clear a fence post, a gate, or the corner of the house? A pad that is a few feet off can make every arrival a fight.
The approach also needs its own concrete or a solid transition. Tires that climb onto a slab edge from loose gravel chip that edge and slowly break it down. A thickened lip or a short apron where the wheels come on spreads that load and keeps the edge from crumbling.
Wheels and jacks put weight in small places
A parked RV does not spread its weight evenly. The tires carry it on small contact patches, and when the leveling jacks or stabilizers come down they put real force onto a few small feet. That is a very different load from a car rolling across a driveway.
So we ask where the wheels will sit and where the jacks will land, and build for those spots specifically. Reinforcement is laid so the steel sits in the slab where it can do its job, held up on supports rather than lying in the dirt. Under the wheel lines and the jack points, the base gets extra attention because that is where any weakness shows up first as a crack or a sunken corner.
Jack pads or blocks under the feet help too, especially on hot days when a slab surface is at its softest under a sharp load. They spread the force and protect the finish.
The base decides it
Most pads that fail were fine on top and wrong underneath. If a pad was poured on loose fill, or on dirt that was graded smooth but never compacted, the heavy end of the rig slowly pushes it down and the slab cracks along the line where firm ground meets soft.
We dig to firm ground, remove anything organic or soft, and bring the base up in thin compacted layers so it is dense all the way through. On fill sections that work takes longer, and it is worth every hour. Where the property has expansive clay, the base and the steel get planned around that movement, because clay that swells wet and shrinks dry will lift and drop a slab every year if it is ignored.
Level enough to live on, sloped enough to drain
Everybody wants the rig to sit level. A dead flat slab, though, holds every rain in a sheet right where you step out. The pad needs a slight fall to one side so water runs off, and the rig levels itself on its jacks for the small difference.
Where that water goes matters on a slope. A wide pad sheds a lot of runoff onto whatever is downhill of it, and if that is a bare bank it will carve a gully over a few storms. We plan the low edge so water leaves onto rock, a swale, or ground that can take it without eroding the base out from under the slab.
Cold months and a parked rig
Around Aguanga a pad sees real freezing in winter. Water that soaks into the surface expands when it freezes, and over many nights that scales the top layer off concrete that was not made for it. Air entrained concrete handles freezing much better, so that is how the mix gets ordered for a mountain pad.
A tow vehicle parked beside the rig after a drive on salted roads drips that salt onto the slab, and salt holds water on the surface and eats at the binder. Sealing the pad, and keeping the joints sealed, gives it a much better chance. A rig sitting on the same spot for a season also keeps that patch of slab shaded and damp, which is one more reason the joints and the finish get looked after.
You can see how we approach RV pads for Aguanga properties. Our RV pads page covers the build itself.
Getting concrete to the spot
On a rural lot the pad is often well back from the road, and the path a mixer truck would take crosses soft ground, a tight gate, or a grade that is too steep for a loaded truck to climb. If the truck cannot get close, the concrete gets pumped. That decision changes the day, so it happens on the first visit along with everything else.
Timing matters too. A big pad is a lot of concrete to place and finish in one go, and the crew has to stay ahead of it the whole time. On a cold morning the slab sets slowly and the finishers wait on it. On a warm afternoon it can stiffen faster than they can work it. We pick the pour day and the start time around the weather and the size of the pad, and if the forecast turns we would rather move the date than rush a slab that has to carry a rig year after year.
A heavy truck crossing your property can also leave ruts, crack an existing slab, or crush a buried line. We look for what is underground before anything heavy drives over it.
Start with a walk around the lot
The best RV pads are planned around the rig and how you park it, then built from the base up. If you have one in mind, send the details through our contact page with the length of your rig and how it gets parked, or call (951) 533-8821. We will come out and look at the spot with you.