The strip of sidewalk in front of a house takes more abuse than almost any other concrete on the lot. Tree roots lift it, utility trenches sink it, delivery trucks park a wheel on it, and the whole block walks over it. When a panel has heaved into a trip hazard or broken into pieces, people call us about replacing it. A walk along the street is a little different from a walk on your own lot, though, and most of that difference shows up before anyone breaks out the old concrete.
Whose concrete it is
The first question on a street-side walk is who owns it. A lot of the walks people think of as theirs actually sit in the public right of way, the strip between the property line and the curb. Work there gets a permit and an inspection, and the agency that owns the strip has a say in thickness, finish and how the new walk meets what is already there. A walk that runs from the street to your front door on your own lot is usually private and simpler.
We sort that out at the start. When the walk is public, the permit comes before the saw, and the inspection gets scheduled before concrete is ordered, because an inspector who finds a problem after the pour leaves you with a slab to break out. When a neighbor shares the run, it helps to talk to them early too. Their panel may be heaved by the same tree, and doing both at once gives one continuous walk with matching joints instead of a patch that ends at the property line.
Shooting grades off everything the walk touches
A new walk has to meet the old concrete around it at the same height. That means the curb, the driveway approach where cars cross the walk and the panels on either side. If the new surface ends up a little high or a little low at any of those edges, it becomes the trip hazard you were trying to get rid of.
We shoot the grades of everything the walk touches before we set forms, and the forms get set to those heights rather than to a level line. Across its width, the walk leans slightly toward the street so rain runs into the gutter and does not sit on the surface or run back toward the house.
Where the walk crosses a driveway approach, that section carries car and truck weight, so it is usually thicker than the rest and gets its own joints on each side. We match the finish across the approach so the line of the walk reads as one piece from the corner to the next property.
Steel and an even thickness under the whole run
Old walks fail where they were thin. A panel that was poured a little shallow over a soft spot is usually the one that cracks across, and a walk with no steel breaks into pieces once a root gets under it. On a replacement we dig out the old base where it has gone soft, bring in fresh material and compact it so the new walk sits on something even from end to end.
The reinforcement goes in on chairs, held up inside the slab where it can do some work. We would rather spend the time lifting steel off the dirt than come back to a cracked panel. Forms are set so the thickness stays the same along the whole run, with the extra depth only where the driveway approach needs it.
Tree roots are their own conversation. Cutting a big root can hurt the tree and may need the owner’s or the city’s sign off, and leaving it means it will lift the new walk again eventually. We show you what we find once the old concrete is out, and you decide from there.
A broom finish people can walk on in the rain
Sidewalks get a broom finish, and the direction of the broom matters. We pull it across the walk, at a right angle to the way people walk, so the texture gives a shoe something to catch on when the surface is wet. A broom run lengthwise looks fine and grips less.
Edges get tooled so they are rounded and hold together, since a sharp, thin edge along the curb or the lawn chips off early. The finish is matched to the old walk where the new section meets it, as close as fresh concrete can get to something that has been weathering for years. Color takes time to settle, and new gray always reads a little lighter at first.
Joints go in at a regular spacing along the run and at every place the walk meets something fixed: a utility box, a meter lid, a tree well, a light pole, the edge of the approach. Concrete cracks out of those points if nobody gives it a line, so each one gets a joint lined up with it.
Keeping the street usable while we work
A sidewalk job happens in front of everyone. Neighbors walk dogs past it and mail carriers need a way through. Before the old concrete comes out we set cones and caution tape along the work area and, where it makes sense, leave a section of walk open or mark a path around it.
Breaking out old panels is loud, so you will know which day that happens. The broken concrete gets hauled off as it comes out instead of sitting stacked on the lawn. Once the new walk is poured, it gets taped off while it cures, because a fresh street-side pour is an open invitation for handprints, bike tires and the occasional set of initials.
Cars stay off the driveway approach until the concrete is ready for that weight, which takes longer than foot traffic. We tell you the wait for your walk at the pour so you can plan where to park. When the tape comes down, the site gets swept and the curb line washed off.
Questions about a street-side walk
Who fixes the curb if it is broken too?
We look at the curb along with the walk. If it is cracked or has sunk, it usually makes sense to replace the section that touches the new walk so the two meet flush. Curb in the public right of way follows the same permit and inspection as the walk, so we fold it into the same paperwork rather than coming back for it later.
Can you just grind the lip down instead?
Sometimes. A small, even lip on a panel that is otherwise sound can be ground flush, and that is a fair repair. A panel that is cracked through, still rising over a root or sunk at one end will keep moving, and grinding it only buys time. We can tell which one you have when we come out and look at it.
Will the new walk match the old one?
As close as fresh concrete gets. New concrete starts lighter and darkens as it ages. We match the thickness, the broom direction, the joint spacing and the edge so the new run reads as part of the street, and the color settles in over time. Replacing a full run between joints, instead of a single panel, also helps it blend.
Send us the address
If the walk in front of your place has heaved, sunk or broken up, the Banning sidewalk page explains how we handle street-side work out here, and our concrete sidewalks service page has the general picture. Call (951) 533-8821 or reach us through the contact page, and we will walk the job and give you a number.