Hemet, CA · California license 1137822 · C-8 Concrete
(951) 533-8821
Home
Services
Services
Residential
Commercial
Service Areas
Service Areas
Riverside County
San Bernardino County
Orange County
Los Angeles County
San Diego County
Kern County
GalleryAboutBlogContactCall (951) 533-8821
Skip to content

A Pool Deck Poured After the Shell

A new pool goes in as a string of trades, and the deck comes near the end of it. The shell is shot, the plumbing is run, the coping is set, the equipment pad is located, and then the concrete crew shows up to pour the surface everyone will actually stand on. Because it comes late, the deck inherits every decision made before it. Getting it right in the pass means planning around the shell, the water, bare feet and a hot afternoon sun, and talking to the pool builder long before any steel goes down.

Where the deck starts and the pool builder stops

The deck is poured after the shell and the coping are in place, and it has to meet the coping edge clean. Before we pour, that edge gets protected. You will often see blue tape along the coping on our pool jobs: it keeps concrete and color off the stone while the crew works right up against it, and it comes off once the deck is finished.

Between the coping and the deck there is a joint, and it matters more than it looks. The pool shell and the deck move differently, and a deck poured tight to the coping with nothing between them will push on it, chip it and eventually crack it. A proper expansion joint there, sealed with a flexible sealant, lets both sides move and keeps water from getting under the deck at the edge.

We talk with the pool builder about heights early. The deck grade at the coping sets the drainage for the whole surface, so the coping elevation needs to be right before we form a single board.

What the deck does with splash-out

A deck that sends water back toward the pool carries dirt, leaves, fertilizer and whatever else is lying around straight into the water. A deck that holds puddles grows slick spots. Either one is a drainage mistake you live with for as long as the deck lasts.

So the surface falls away from the water from the coping outward, toward deck drains or a planted edge that can take it. On a big deck, drains get placed in the low spots and the slope runs to them in more than one direction, which we lay out with the forms and string lines before any steel goes down. Near the house, the deck falls away from the wall as well, because a deck that slopes toward the foundation is just a different drainage mistake.

If there are deck drains, the lines are run and capped before the pour, and we check that the grates sit at the right height for the surface. A drain set a little high turns into its own puddle with a grate in the middle.

Grip for wet feet and a surface you can stand on

Pool decks are walked on barefoot and wet, so grip comes first. A smooth troweled finish is easy to clean and dangerous around water. We use a light broom, a salt finish, a textured surface or a stamped pattern with enough relief to give a wet foot some purchase, and we pick it with the people who will be using the pool, kids included.

The pass gets hot afternoons, and dark concrete in full sun gets uncomfortable fast. A lighter color and a textured surface stay more tolerable underfoot than a dark, smooth one. Where you want a darker look, such as the charcoal slate pattern we stamp on some decks, it helps to put it where shade falls in the afternoon, or to pair it with a lighter border closer to the loungers.

Shade itself is worth planning now. A shade structure or a pergola needs footings, and those go in before the deck, or the deck gets cut later to make room for them.

Stamped color and the sealer that goes over it

A stamped and colored deck gets its look from the pattern, the color and the sealer on top. The sealer is where slip resistance can go wrong. A glossy sealer makes the color pop on the day it goes on, and it can turn a textured stamp slick as glass when it gets wet. Around a pool we use a sealer suited to foot traffic around water, and on a stamped deck it often gets a grit additive mixed in so the surface keeps its grip.

Sealer also wears. Pool chemicals, splash-out and sun break it down over time, and a deck that has lost its sealer starts to fade and take on water. You will get told how to tell when it is due and what to use, along with what to keep off it, such as harsh cleaners and pool chemicals spilled straight onto the surface.

Color is chosen against a sample, outside, in the light you will see it in. Swatch cards under a store light rarely look the same once they are poured in the pass.

Joints around the curve and what is buried under the deck

A free-form or kidney-shaped pool means the deck curves, and the joint layout has to follow it. Joints run out from the curve toward the outer edge, spaced so each panel keeps a reasonable shape, and they get lined up with any inside corner where the deck wraps around steps or a spa. On a stamped deck we try to hide them in the grout lines of the pattern so they do not read as cuts through the stone.

Before any steel goes down, everything that runs under the deck gets located and marked: the return and suction lines, the drain lines, electrical for lights and equipment, and gas to a heater or a fire feature. The equipment pad gets placed at the same time, with room for the pump, the filter and whoever has to service them. Our steel goes in on chairs over a graded base around the shell after that layout is set, because cutting into a finished deck to find a buried line is the worst way to learn where it went.

Pool deck questions

How long after the pool is shot can the deck go in?

That depends on the pool builder’s schedule more than on us. The shell, plumbing, coping and any pressure testing on the lines come first, and the deck follows once those are done and the coping grade is set. We coordinate the date with the builder so nobody pours around open work, and so the deck is not sitting finished while trucks still need into the yard.

What should I do with the deck the first season?

Rinse pool chemicals and salt off the deck rather than letting them dry on it, keep the drains clear of leaves and grit, and watch the sealer where feet go most. When the surface starts to look dull or water stops beading on it, call about resealing with the same kind of product that is on it now.

Can you pour a new deck around an existing pool?

Usually, yes. The old deck comes out carefully so the coping is not damaged, the base is checked and rebuilt where it is soft, and the new deck goes in with a proper joint at the coping. If the coping itself is loose or cracked, that is a repair for a pool contractor and it gets done first.

Bring us in before the shell is shot

If you are building a pool or replacing a tired deck, read the pool deck page for Banning for how we sequence a deck around a new pool, or the broader pool decks page. Phone (951) 533-8821, or send the details along with your pool builder’s schedule, and we will come out and look at it.